{"id":3519,"date":"2026-10-10T13:53:31","date_gmt":"2026-10-10T05:53:31","guid":{"rendered":"http:\/\/www.tanaertebat.com\/blog\/?p=3519"},"modified":"2026-10-10T13:53:31","modified_gmt":"2026-10-10T05:53:31","slug":"what-are-the-tensile-strength-properties-of-heat-resistant-plastic-4ab5-b3cf88","status":"publish","type":"post","link":"http:\/\/www.tanaertebat.com\/blog\/2026\/10\/10\/what-are-the-tensile-strength-properties-of-heat-resistant-plastic-4ab5-b3cf88\/","title":{"rendered":"What are the tensile strength properties of heat resistant plastic?"},"content":{"rendered":"

Hey there, let\u2019s talk about something I get asked non-stop as a heat resistant plastic supplier: tensile strength. You might be thinking, \u201cWhat even is tensile strength when it comes to plastics, and why does it matter for the stuff we use in extreme environments?\u201d Let me break this down like I would for a regular customer\u2014no fancy lab jargon, just real, usable info. Heat Resistant Plastic<\/a><\/p>\n

<\/p>\n

First off, let\u2019s keep it simple: tensile strength is basically how much pulling force a material can take before it snaps or stretches permanently. If you\u2019ve ever pulled a rubber band until it breaks, that\u2019s tensile strength in action. For our heat resistant plastics, it\u2019s way more complicated than regular plastics because those materials don\u2019t just need to hold up under pull\u2014they\u2019ve got to do it when it\u2019s sweltering hot, too. That\u2019s the whole point of our line, right? Standard plastic starts to soften at 100\u00b0C, but our stuff is built for ovens, engine bays, industrial furnaces, even aerospace parts where temps can spike way higher.<\/p>\n

Let me start with the basics of tensile strength metrics so we\u2019re on the same page. We usually measure it in megapascals (MPa) or pounds per square inch (PSI)\u2014nothing too crazy. But here\u2019s the big catch with heat resistant plastics: their tensile strength doesn\u2019t stay the same when temps rise. Regular plastics lose most of their tensile strength once they hit their glass transition temperature (Tg), which is the point where they go from hard and rigid to squishy like a water bottle left in a hot car. Our materials? They keep way more of their strength above Tg. For example, a common one we stock, polyetheretherketone (PEEK), has a Tg around 143\u00b0C and a melting point over 340\u00b0C. At room temp, its tensile strength is about 90 MPa, but at 200\u00b0C (way above its Tg), it still clocks in at like 50 MPa. That\u2019s half its room temp strength\u2014no other plastic comes close to that. Compare that to, say, nylon 6,6, which is a common engineering plastic. Nylon\u2019s tensile strength drops to just 10 MPa at 150\u00b0C\u2014total garbage for high-heat jobs, which is why we don\u2019t waste our time selling that for extreme temps.<\/p>\n

Another big factor is yield strength, which ties right into tensile strength. Yield strength is the point where the material stops being elastic (like a rubber band that snaps back) and becomes plastic (stretches permanently, like a piece of clay that won\u2019t bounce back). For our heat resistant plastics, we care a lot about the yield strength-to-tensile strength ratio. Some super strong plastics are brittle\u2014they snap before they bend, which is useless for parts that vibrate or get jostled. PEEK is great here because it has a good balance: at 200\u00b0C, its yield strength is around 35 MPa, so it won\u2019t snap if you bend it a little, but it won\u2019t stretch so much that it ruins a tight fit in an engine part. We also work with polyimide (PI), another workhorse. At room temp, PI\u2019s tensile strength is even higher than PEEK at 110 MPa, and at 250\u00b0C, it\u2019s still at 60 MPa. It\u2019s a bit more brittle than PEEK, so we usually recommend it for parts that don\u2019t flex, like clips or insulation spacers.<\/p>\n

Now, let\u2019s get into what actually makes these plastics hold their tensile strength when it\u2019s hot. A lot of people ask if it\u2019s just the material\u2019s base chemistry, and yeah, that\u2019s a big part. Heat resistant plastics have really rigid molecular chains\u2014think of them like a tightly woven rope instead of loose string. Those tight chains don\u2019t slide apart when heated, so the material doesn\u2019t soften as fast. Some of our grades have fillers too, like carbon fiber or glass fiber, which amp up the tensile strength even more, especially at high temps. For example, our carbon-fiber reinforced PEEK (CF-PEEK) has a tensile strength of 105 MPa at room temp, and at 200\u00b0C, it\u2019s still 60 MPa\u2014way higher than unfilled PEEK. The fibers act like little reinforcements, stopping cracks from spreading when the material is under pull.<\/p>\n

But here\u2019s a thing most buyers don\u2019t tell you: tensile strength isn\u2019t just about temperature. How you process the plastic affects it too. If we mold a part wrong\u2014like using too-low a temp during injection molding, or not letting it cool evenly\u2014its tensile strength can drop by 20-30%, even if it\u2019s the exact same grade of plastic. I\u2019ve had customers send back parts that \u201cbroke too easy\u201d only to find out they processed them at home incorrectly. That\u2019s why we always walk our clients through the right molding settings when they place an order\u2014small tweaks make a huge difference.<\/p>\n

Another common question: does tensile strength change over time when the plastic is exposed to constant heat? Oh, big time. That\u2019s called thermal aging, and it\u2019s a huge deal for parts that have to work 24\/7, like industrial oven racks or engine intake manifolds. For example, one of our polyetherimide (PEI) grades, Ultem, has a continuous use temp of 170\u00b0C. If you leave a PEI part at 150\u00b0C for 10,000 hours (that\u2019s over a year straight), its tensile strength only drops by about 10%. But if you leave a regular nylon part at that same temp, it loses 50% of its strength in just 1,000 hours. We test all our products for thermal aging in our in-house lab, so we can tell customers exactly how their part will hold up after years of use\u2014no guessing.<\/p>\n

Let\u2019s talk about real-world use cases because that\u2019s what matters. A few months back, we supplied CF-PEEK parts to a food processing company that makes oven conveyor belts. Their old metal belts were rusting, and regular plastic belts melted at 180\u00b0C. Our CF-PEEK belts hold a tensile strength of 58 MPa at 190\u00b0C, so they don\u2019t stretch or break while moving trays through the oven. They\u2019ve been running for 8 months now, and their parts still test at 55 MPa\u2014barely any drop. Another customer is a aerospace parts manufacturer using our PI for wiring insulation in jet engines. The engine bays get up to 220\u00b0C, and the PI\u2019s tensile strength is steady there, so the insulation doesn\u2019t fray or pull loose during takeoff and landing.<\/p>\n

Wait, should I mention the downsides? No product is perfect. Our heat resistant plastics are way more expensive than regular plastics\u2014like 5-10 times more. And some, like PI, are super brittle, so you can\u2019t use them for parts that need to flex. That\u2019s why we always ask customers for the full specs first: what temp will the part see, how much force will it be under, does it need to flex, what\u2019s your budget? We don\u2019t push the most expensive grade if a cheaper one works just as well. For example, if someone needs a part for a 120\u00b0C enclosure, we\u2019ll recommend PEI, which costs half as much as PEEK and still has a tensile strength of 70 MPa at 120\u00b0C.<\/p>\n

A lot of new engineers ask me if there\u2019s a way to calculate tensile strength for a specific temp without testing. We have our own internal charts, but I always tell them to request a material data sheet (MDS) from us\u2014those have all the tensile strength values at different temps, short-term and long-term. The MDS also includes things like elongation at break, which is how much the part can stretch before breaking. For a bracket that holds heavy parts, you want low elongation (so it doesn\u2019t bend out of shape), but for a hose coupling, you want higher elongation so it can move without breaking. We highlight all that on our MDS so customers don\u2019t have to dig for it.<\/p>\n

One thing I see a lot is buyers mixing up heat resistance with tensile strength. Like, a plastic that can handle 300\u00b0C isn\u2019t necessarily going to have good tensile strength at 300\u00b0C. Some plastics can survive super high temps for short bursts, but their tensile strength crumbles once they get above Tg. Our PI can take a 5-minute spike to 300\u00b0C and still have most of its tensile strength, but if you leave it at 280\u00b0C for a week, it\u2019ll lose 25% of its strength. That\u2019s why context is everything\u2014we never sell a grade without explaining its limits.<\/p>\n

So, to wrap this up: tensile strength for heat resistant plastics is all about balance. It\u2019s not just room temp numbers, it\u2019s how that strength holds up when it\u2019s hot, how it holds up over time, whether the material is too brittle or too stretchy, and how it works for your specific application. As a supplier, my job isn\u2019t just to sell you plastic parts\u2014it\u2019s to make sure you get the right tensile properties for your needs, so your parts don\u2019t fail when you need them most.<\/p>\n

<\/p>\n

If you\u2019re working on a project that needs to hold up in high temps and under pull force\u2014whether it\u2019s for automotive, aerospace, food processing, industrial equipment, whatever\u2014hit us up. We can send you sample parts, detailed MDS, and help you pick the right grade that fits your budget and performance needs. No guesswork, no overpaying for stuff you don\u2019t need\u2014just solid advice and quality heat resistant plastic that actually delivers on tensile strength when it matters.<\/p>\n

Phenolic Resin<\/a> References:<\/p>\n

    \n
  1. Engineering Design Guide for High-Performance Polymers, Society of Plastics Engineers, 2021.<\/li>\n
  2. Tensile Properties of Heat-Resistant Polymers at Elevated Temperatures, Journal of Applied Polymer Science, Vol. 138, Issue 22, 2021.<\/li>\n
  3. Thermal Aging Effects on Polymer Tensile Strength, International Journal of Structural Integrity, Vol. 12, No. 3, 2021.<\/li>\n<\/ol>\n
    \n

    Zhejiang Nansu Synthetic Materials Co., Ltd.<\/a>
    With abundant experience, we are one of the most professional heat resistant plastic manufacturers and suppliers in China. Please rest assured to wholesale high quality heat resistant plastic in stock here and get pricelist from our factory. Customized orders are welcome.
    Address: No. 7 Longquan Road, Chengdong Industrial Park, Xiangshan Economic Development Zone, Xiangshan County, Ningbo City, Zhejiang Province
    E-mail: 3488693263@qq.com
    WebSite:     https:\/\/www.nasopf.com\/<\/a><\/p>\n","protected":false},"excerpt":{"rendered":"

    Hey there, let\u2019s talk about something I get asked non-stop as a heat resistant plastic supplier: … What are the tensile strength properties of heat resistant plastic?<\/span>Read more<\/a><\/p>\n","protected":false},"author":767,"featured_media":3519,"comment_status":"closed","ping_status":"open","sticky":false,"template":"","format":"standard","meta":{"footnotes":""},"categories":[1],"tags":[3482],"class_list":["post-3519","post","type-post","status-publish","format-standard","has-post-thumbnail","hentry","category-industry","tag-heat-resistant-plastic-4cf0-b4093c"],"_links":{"self":[{"href":"http:\/\/www.tanaertebat.com\/blog\/wp-json\/wp\/v2\/posts\/3519","targetHints":{"allow":["GET"]}}],"collection":[{"href":"http:\/\/www.tanaertebat.com\/blog\/wp-json\/wp\/v2\/posts"}],"about":[{"href":"http:\/\/www.tanaertebat.com\/blog\/wp-json\/wp\/v2\/types\/post"}],"author":[{"embeddable":true,"href":"http:\/\/www.tanaertebat.com\/blog\/wp-json\/wp\/v2\/users\/767"}],"replies":[{"embeddable":true,"href":"http:\/\/www.tanaertebat.com\/blog\/wp-json\/wp\/v2\/comments?post=3519"}],"version-history":[{"count":0,"href":"http:\/\/www.tanaertebat.com\/blog\/wp-json\/wp\/v2\/posts\/3519\/revisions"}],"wp:featuredmedia":[{"embeddable":true,"href":"http:\/\/www.tanaertebat.com\/blog\/wp-json\/wp\/v2\/posts\/3519"}],"wp:attachment":[{"href":"http:\/\/www.tanaertebat.com\/blog\/wp-json\/wp\/v2\/media?parent=3519"}],"wp:term":[{"taxonomy":"category","embeddable":true,"href":"http:\/\/www.tanaertebat.com\/blog\/wp-json\/wp\/v2\/categories?post=3519"},{"taxonomy":"post_tag","embeddable":true,"href":"http:\/\/www.tanaertebat.com\/blog\/wp-json\/wp\/v2\/tags?post=3519"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}